For downloading the Tools, Driver and Firmware use the following link:
//youyeetoo.com/blog/nanopi-r5s-ysdpnanor5sa-135
Tips: The 4GB version of eMMC is upgraded from 16GB to 32GB
Note:Please note the type what you want:
Bundle 1:NanoPi R5S 2G
Bundle 2:NanoPi R5S Kit (with Metal Case) 2G
Bundle 3:NanoPi R5S 2G+32G TF Card
Bundle 4:NanoPi R5S Kit (with Metal Case) 2G+32GB TF Card
Bundle 5:NanoPi R5S 2G +Power (5V)+Type-C cable
Bundle 6:NanoPi R5S Kit (with Metal Case) 2G+Power (5V)+Type-C cable
Bundle 7:NanoPi R5S Kit (with Metal Case) 4G
Bundle 8:NanoPi R5S Kit (with Metal Case) 4G +32GB TF Card +Power(5V)+Type-C cable
Introduction
-
The NanoPi R5S is a RK3568 SoC based ARM board.
Hardware Spec
-
SoC: Rockchip RK3568B2
-
CPU: Quad-core ARM Cortex-A55 CPU, up to 2.0GHz
-
GPU: Mali-G52 1-Core-2EE,supports OpenGL ES 1.1, 2.0, and 3.2, Vulkan 1.0 and 1.1, OpenCL 2.0 Full Profile
-
VPU: 4KP60 H.265/H.264/VP9 video decoder, 1080P60 H.264/H.265 video encoder
-
NPU: Support 0.8T
-
-
RAM: 2GB LPDDR4X
-
Flash: 8GB eMMC
-
Ethernet: one Native Gigabit Ethernet, and two PCIe 2.5Gbps Ethernet
-
USB: two USB 3.0 Type-A ports
-
HDMI:
-
support HDMI1.4 and HDMI2.0 operation
-
support up to 10 bits Deep Color modes
-
support up to 1080p@120Hz and 4096×2304@60Hz
-
support 3-D video formats
-
-
PCIe: M.2 Key M, PCIe2.1 x1, support NVME, PCIe WiFi etc
-
microSD: support UHS-I
-
GPIO:
-
12-pin 0.5mm FPC connector
-
up to 1x SPI, up to 3x UARTs, up to 4x PWMs, up to 8x GPIOs
-
-
SD/MMC/SDIO/I2S:
-
2×8-pin 1.27mm connector
-
Compatible with SDIO3.0 protocol
-
Compatible with SD3.0, MMC ver4.51
-
4bits data bus widths
-
1x I2S with 2x SDO and 3x SDI
-
-
Debug: one Debug UART, 3 Pin 2.54mm header, 3.3V level, 1500000bps
-
LEDs: 4 x GPIO Controlled LED (SYS, WAN, LAN1, LAN2)
-
others:
-
2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS
-
MASK button for eMMC update
-
one 5V Fan connector
-
-
Power supply: USB-C, support PD, 5V/9V/12V input
-
PCB: 8 Layer, 62x90x1.6mm
-
Ambient Operating Temperature: 0℃ to 70℃
Diagram, Layout and Dimension
Layout
-
12-pin GPIO
Pin# |
GPIO |
SPI |
UART |
PWM |
POWER |
Description |
1 |
VCC3V3_SYS |
3.3V power output |
||||
2 |
VCC3V3_SYS |
3.3V power output |
||||
3 |
GPIO3_C3 |
SPI1_CLK_M1 |
UART5_RX_M1 |
3.3V level |
||
4 |
GND |
|||||
5 |
GPIO3_C2 |
SPI1_MISOI_M1 |
UART5_TX_M1 |
3.3V level |
||
6 |
GPIO3_A1 |
SPI1_CS0_M1 |
3.3V level |
|||
7 |
GPIO3_C1 |
SPI1_MOSI_M1 |
3.3V level |
|||
8 |
GND |
|||||
9 |
GPIO4_C5 |
UART9_TX_M1 |
PWM12_M1 |
3.3V level |
||
10 |
GPIO4_C6 |
UART9_RX_M1 |
PWM13_M1 |
3.3V level |
||
11 |
GPIO3_C4 |
UART7_TX_M1 |
PWM14_M0 |
3.3V level |
||
12 |
GPIO3_C5 |
UART7_RX_M1 |
PWM15_IR_M0 |
3.3V level |
-
2×8-pin SDIO/I2S
Pin# |
GPIO |
SD/MMC/SDIO |
I2S |
POWER |
Description |
1 |
VCC5V0_SYS |
5V power output |
|||
2 |
VCC5V0_SYS |
5V power output |
|||
3 |
GPIO3_C6 |
SDMMC2_D0_M0 |
I2S1_MCLK_M1 |
1.8V level |
|
4 |
GPIO3_C7 |
SDMMC2_D1_M0 |
I2S1_SCLK_TX_M1 |
1.8V level |
|
5 |
GND |
||||
6 |
GND |
||||
7 |
GPIO3_D0 |
SDMMC2_D2_M0 |
I2S1_LRCK_TX_M1 |
1.8V level |
|
8 |
GPIO3_D3 |
SDMMC2_CLK_M0 |
I2S1_SDI1_M1 |
1.8V level |
|
9 |
GND |
||||
10 |
GND |
||||
11 |
GPIO3_D1 |
SDMMC2_D3_M0 |
I2S1_SDO0_M1 |
1.8V level |
|
12 |
GPIO3_D2 |
SDMMC2_CMD_M0 |
I2S1_SDI0_M1 |
1.8V level |
|
13 |
GND |
||||
14 |
GND |
||||
15 |
GPIO3_D5 |
SDMMC2_PWREN_M0 |
I2S1_SDI3_M1 |
1.8V level |
|
16 |
GPIO3_D4 |
SDMMC2_DET_M0 |
I2S1_SDI2_M1 |
1.8V level |
-
Debug UART Pin Spec
Pin#
Assignment
Description
1
GND
0V
2
UART2DBG_TX
output
3
UART2DBG_RX
intput
-
USB Port
Each USB 3.0 port has 1.4A overcurrent protection.
-
RTC
RTC backup current is 0.25μA TYP (VDD =3.0V, TA =25℃).Connector P/N: Molex 53398-0271
CPU |
Model: Rockchip RK3568B2 |
GPU |
Mali-G52 1-Core-2EE, supports OpenGL ES 1.1/2.0/3.2, Vulkan 1.0/1.1, OpenCL 2.0 Full Profile |
VPU |
4KP60 H.265/H.264/VP9 video decoder, 1080P60 H.264/H.265 video encoder |
NPU |
Support 0.8T |
Memory |
RAM: 2GB/4GB LPDDR4X |
Storage |
MicroSD Slot: MicroSD x1, support UHS-I, for external storage up to 128GB |
Connectivity |
Ethernet: Native Gigabit Ethernet x1, RTL8211F-CG chip |
Video Output |
HDMI: support HDMI1.4 and HDMI2.0 operation |
USB |
USB 3.0 Host x2: USB Type A |
Pin-header |
GPIO: 12-pin 0.5mm FPC connector |
LED |
SYS LED(Red) x1 |
Button |
MASK Button x1 for eMMC update |
Others |
RTC Battery: 2 Pin 1.27/1.25mm RTC battery input connector for low power RTC IC HYM8563TS |
Power |
DC 5V/3A, via USB-C connector or Pin header |
OS Support |
FriendlyWrt 21.02 |
Kernel version |
Linux-5.10-LTS |
PCB |
8 Layer |
Dimension |
62x90x1.6mm mm(without Case) / 68×94.5x30mm mm(with Case) |
Weight |
57.5g(without Case) / 260g(with Case) |
[Tech-support]
Wiki: //youyeetoo.com/blog/
Forum: bbs.youyeetoo.com
ExpertSupport: [email protected]
Payment
1. If the payment is not available, your order will be closed automatically.
2. Seller are responsible for any insurance, problems and damage which caused by shipping service such accidents, delays or other issues.Besides the buyer should to be responsible for any tax and/or dutycharged by their country.
Shipping Choice
Self-Help Shipping Guide
Shipment
1. All item will be shippedwithin 48 hours on receipt of cleared payment.(The earlier you pay, the earlier we ship your order.)
2. If you need faster shipment, please choose DHL or EMS or FedEx IP(Shipping fare paid by yourself). Or we will deliver via the default method.
3. Please make sure that your shipping address is 100% correct
4. We ship items to worldwide with delivery time guarantee
Contact us
1.If you have any requestplease don’t hesitate to contact us at first time we will help you and solve your issue within 24 hours.
2. All emails will be answered within 1 business day. If you do not receive our reply, please kindly re-sent your email and we will reply you as soonas possible.
3. Warranty services are for replacements only, any problem please kindly email us frist, we will accept your advise & request.
Return&Refund
1.Refund or resendnew for any orders due to the product quality problem.
2.We accept any unused itemin its original package as return within 7 days of delivery. Buyers must provide the tracking number, specific reason forthe return.
3. if it’s buyer’ s reason lead to the return package, buyers need to pay for round shipping fare.
4. We will refund to buyer after we receive the returns in its original condition package. Or buyers could choose to have a replacement.
FeedBack
1.As your feedback is really important to us, please take a few minute to leave the positive feedback if you are satisfied with our products and service .Also we will do the same for you ASAP. Thanks!
2. Please don’t hesitate to contact usbefore you leaving negative or neutralfeedback. We will try our best to resolve your problem and meet your need.